OVERVIEW Key Features of the SB541C •Heavy-duty hydraulically controlled side tension rails •Cast-iron hay wedges for a longer life •Long, heavy bale case for improved bale shape and easier handling •The fast plunger speed and longer plunger stroke packs uniform, dense bales in all crop conditions •?High-strength steel used throughout the plunger mechanism? FEATURES Plenty of Sturdy Tines and an Adjustable Pickup Gauge Wheel Crank out high-quality bales in all kinds of crops and crop conditions with the SB Series small square balers. They are all about productivity. With four models, these balers get the job done right with high-capacity features like wide pickups and heavy-duty, smooth rotary feeding systems.
Plenty of Sturdy, Closely Spaced, Curved Finger Tines
• Gently lift the crop while keeping leaves intact • Rugged tine bars run on sealed ball bearings for long life and trouble-free operation
Standard Pickup Gauge Wheels Adjust to Five Positions
• Guides the pickup through the contours of the field • Allows you to get every bit of the windrow
Raise Pickup for Transport
• Select the manual latch or optional hydraulic pickup lift
Provides For A Uniform, Well-Shaped Bale Huge 283-sq in (1,826-sq cm) feed opening allows SB balers to swallow large, uneven windrows. From here, the dependable Case IH feeding system takes over, providing a smooth flow of crop into the bale chamber for a uniform, well-shaped bale.
SB521 Feeding System
• Six feeder tines gently move the crop into the bale chamber, saving high-protein leaves • Chain-driven system for durability and easy servicing
Easy Bale Density Control
All SB Series balers allow for easy bale density control by adjusting the tension applied to the bale chamber. For manual density control, tension springs are an economical choice.
• Provides "set-it-and-forget-it" convenience • Ensures consistent bale weight and density
Case IH Small Balers Ties and Twists
Case IH small bales hold up to handling from the rack to the elevator and from the barn to the bunk.
Dependable Gear-driven Twine Knotters:
• Hard-surface material at all wear points • Bill hooks are chrome plated for extra durability and reduced maintenance • SB541 is also available with a gear-driven wire twister
SPECIFICATIONS Make Case IH Model SB541c Bale size Bale cross section, h x w, in (mm) 14 x 18 (356 x 457) Bale length range, in (mm) 12 to 52 (305 to 1321) Density control, standard Adj hydraulic density Density control, optional No option Bale thrower compatible No Pickup Pickup position Offset to right side Sweep width on flare, in (mm) 80 (2030) Sweep width inside, in (mm) 75 (1900) Width between outside tines, in (mm) 67.5 (1714) Tine spacing, in (mm) 2.63 (67) Number of tines 156 Number of tine bars 6 Windguard description 13 rods Standard pickup lift Hydraulic Optional pickup lift No option Pickup protection V-belt slippage & lost motion reel drive Feeder Feeder Description Rotary feeder w/ packer Feeder opening, sq in (sq cm) 284 (1832), right side entry Plunger Plunger speed, strokes/min 93 Plunger stroke, in (mm) 30 (762) Tying mechanism Tying mechanism type HD Knotter Tying capacity (twine), balls 8 heavy duty Tying capacity (wire), coils No wire Main Drive Flywheel diameter, in (mm) 22 (559) Flywheel weight, lbs (kg) 248 (112) PTO Driveline Std three-joint, Category 6 PTO Speed, rpm 540 Main drive protection Shearbolt, overrunning & slip clutches Tires Standard tire, left 14L x 16.1, 6PR Standard tire, right 11L x 14, 6PR Dimensions Max. height, in (mm) 71 (1803) Width, in (mm) 120 (3048) Length w/o bale chute, in (mm) 217 (5512) Length w/bale chute, in (mm) 259 (6580) Weight Weight w/twine tie, lbs (kg) 3,940 (1787) Weight w/wire tie, lbs (kg) No wire
Photos
Highlights
Armstrong
New
C002F
2022
Case IH
Small Square Balers SB541C
00000000YNN310326
RED
0
Other
Available
Inside: 75 in. (1 905 mm) | on Flare: 80 in. (2 032 mm)
Specifications
2022
Case IH
Small Square Balers
SB541C
Square Baler
Min: 75 hp
Std: 3 joint, category 6, with Power-Pivot bearing
Drive Mechanism: Gear and shaft
Heat treated, steel alloy hypoid gears run in oil
Left/ Right: 14L×16.1 , 6PR / 11×14, 6PR
93 spm
Cross Section: 14×18 in. (356×457 mm) | Flywheel Diameter: 22 in. (559 mm) | Feeder Opening: 283 sq. in. (0.182 sq. m)
12 to 52 in. (305 to 1 321 mm) | Stroke: 30 in. (762 mm)
Inside: 75 in. (1 905 mm) | on Flare: 80 in. (2 032 mm)
Number of Teeth: 156 | Tine Bars: Six tooth bars | Protection: V-belt to chain, with “lost-motion” reel drive | Type: Rotary feeder with packer | Tying Type: HD knotter | Protection: Shear bolt | Capacity (Twine): 6 balls | Protection: Shear bolt, overrunning and slip clutches | Type feeder: Rotary feeder with packer
Flywheel: 248 lb. (112 kg) | Twine Tie: 3,940 lb. (1 787 kg)